CleO Modules
NerO Module
FT51A Modules
FT9xx Modules
EVE 2 Modules
SuperSpeed Modules
EVE Modules
Raspberry Pi
USB - RS232/422/485
Development Modules
Application Modules
DLP Modules
3rd Party Modules
Sales Network
Web Shop
Contact Us




 FT9xx Development Modules
Based upon the FT32 high performance, 32 bit RISC core, the FT9xx series provides a plethora of connectivity options, making it the ideal choice for advanced technology bridging solutions. By executing instructions from shadow RAM, rather than flash memory, the FT9xx can operate at true Zero Wait States (0WS) up to 100MHz with 310 DMIPS performance.

A range of modules are provided, designed to assist with design and development with the series.
 MM900EV Development Modules

The MM900EV development modules provide full hardware feature support for the FT90x MCU in a variety of form factors.The modules also provide a connector for accessing external plug-in hardware over an SPI interface. Targeted applications for the module include home security, HMI and automation systems,USB capability products, embedded multimedia applications and a range of other industrial control systems. There are four module types available: the MM900EV1A, which comes without a camera, MM900EV2A with a front-facing CMOS camera, MM900EV3A, equipped with a rear-facing CMOS camera. The MM900EV-Lite is optimized for HMI and embedded display applications.

Key Features:

  • FT90x 100-pin QFN package MCU.
  • RJ45 with built in magnetics for 10/100Mbps Ethernet transfer.
  • Standard USB-A connector to support USB device connection.
  • Micro-B USB for connecting to a USB host or providing a power supply over USB.
  • In built audio codec for stereo audio output with 3.5mm headphone jack and mono microphone input.
  • Debugger interface for FT90x flash programming and EFUSE configuration.
  • +5V alternative power supply DC connector.
  • 2x5 pins 1.27mm pitch female Micro-MaTch connector for software download.
  • 2x20 pins 2.54mm pitch female header support for external feature expansions.
  • 24 pins 0.5mm pitch camera connector and two RGB LEDs (MM900EV2A/3A modules).
  • MicroSD card socket supporting SD3.0 specification.
  • 2x8 pins 2.54mm pitch dual entry female header and 16 pins 0.5mm pitch FFC/FPC connectors for SPI master to support LCD display modules.
  • MM900EVxA Datasheet
  • MM900EV-LITE Datasheet
 MM930Mini Module

The MM930Mini Module is a USB microcontroller development module in the Bridgetek product range. It utilizes the FT930Q bridge chip which can handle all USB signalling and protocols. It is ideal for development purposes to quickly prove functionality of adding USB to a target design.

Key Features:

  • USB 2.0 Hi-Speed compatible.
  • Reduced development time
  • Rapid integration into existing systems
  • USB powered no external power supply needed
  • Based on the USB Hi-Speed FT930Q device
  • Entire USB protocol handled by D2xx hardware engine
  • USB micro-B connector common on many commercial devices
  • On-board 500mA 3.3V LDO regulator, 12MHz crystal, 32kHz crystal
  • Asynchronous Serial data transfer rates from 300 baud to 12 Mbaud at TTL levels
  • One SPI master supports single / dual / quad modes of data transfer. Clock rate is up to 25 MHz
  • One SPI slave support single data transfer with 25MHz clock
  • I2C bus interface can be configured as master or slave, with data transfers up to 3.4Mbps
  • UHCI / OHCI / EHCI host controller compatible
  • One SPI slave support single data transfer with 25MHz clock


The UMFPD2A debugger/programmer module provides a USB bridge between the FT9xx Eclipse IDE development tools runnng on a PC and the FT900 1-wire debug pin. This module can be used to program and debug firmware running on the FT9xx series.

Key Features:

  • Hi-Speed USB to one-wire interface converter
  • Hi-Speed USB to MPSSE interface converter
  • Hi-Speed USB to UART interface converter
  • Provides H/W Reset# signal
  • Provides multiple generic GPIO control signals
  • PWREN# line to control +5 power supply
  • Fuse protected with 0.5A hold current and schottky diode on the output power line
  • Two dedicated GPIOs to control VPP and FRSC power supplies
  • Three LEDs for power supply indication
  • 2X5 way 1.27mm pitch Micor-MaTch socket
  • 2X6 way 2.54mm pitch through hole pin header
  • Micro-B type USB port
  • Micro-MaTch Male to Male 10 pin ribbon cable


     Ordering Information

    MM900EV1A FT90x Development Module
    MM900EV2A FT90x Development Module with front-facing CMOS camera
    MM900EV3A FT90x Development Module with rear-facing CMOS camera
    MM900EV-Lite Cut down FT90x Development Module
    MM930Mini USB microcontroller development module
    VA-PSU-UK1 Accessory - UK Model 5V/1A USB Power Supply (Mfr # JX-B0520C-1-B)
    VA-PSU-US1 Accessory - US Model 5V/1A USB Power Supply (Mfr # JX-B0520B-1-B)
    VA-PSU-EU1 Accessory - EU Model 5V/1A USB Power Supply (Mfr # JX-B0520A-1-B)
    ME810A-HV35R Daughter board - FT810 Development Module with 3.5 inch HVGA TFT LCD and fitted bezel
    ME812A-WH50R Daughter board - FT812 Development Module with 5.0 inch WVGA TFT LCD and fitted bezel
    ME813A-WH50C Daughter board - FT813 Development Module with 5.0 inch WVGA TFT LCD
    Daughter board - FT812 Development Module with 5.0 inch 800*480 TFT LCD
    Daughter board - FT813 Development Module with 5.0 inch 800*480 TFT LCD
    VA-FC-1M-BKW Accessory - Flat USB A to Micro B Cable 1M - Black and White
    VA-FC-1M-BLW Accessory - Flat USB A to Micro B Cable 1M - Blue and White
    UMFTPD2A Daughter board - MM900EV MCU Debugger Module

     FT9xx Tool Chain
    • Click here to download the FT9xx Series Toolchain to enable code development and debug for the FT9xx series Development Modules.

    © Future Technology Devices International Ltd.