FT2232C MPSSE Projects

MPSSE Example Projects

This page contains examples specific to the Multi-Protocol Synchronous Serial Engine (MPSSE) of the FT2232D and FT2232H devices.

FTCI2C DLL
FTDI have produced a DLL to handle all the MPSSE commands necessary to interface to a device using the I2C protocol. A separate page has been created where the FTCI2C DLL can be downloaded, along with code examples.
FTCJTAG DLL
FTDI have also produced a DLL to handle all the MPSSE commands necessary to interface to a device using the JTAG protocol. As with our FTCI2C DLL, a separate page has been created where the FTCJTAG DLL can be downloaded, along with code examples.
FTCSPI DLL
Following the popularity of the FTCI2C and FTCJTAG DLLs, the FTCSPI DLL has been made available for interfacing the FT2232D to SPI devices. Please note that the FT2232D can only act as an SPI master and not an SPI slave device.

The MPSSE can be configured directly using D2XX commands. The following Delphi examples on this page illustrate how to achieve this for several popular protocols:

AT-Bus with Host Emulation Mode
JTAG
I2C
SPI

Customer contributions are always welcome.

Jörn Kaipf has created a FT2232 based JTAG debugger and has kindly made his design freely available. Please visit his web site to learn more about his OOCD-Link project.

Host Bus Emulation Mode

Overview

This is an example project that demonstrates using the FT2232D's Multi-Protocol Synchronous Serial Engine (MPSSE) controller to perform MCU host bus control of an AT-Bus. The executable application and the full project code (in Delphi) are provided.

Requirements

This project is designed to run on Windows 2000 or Windows XP and requires FTDI's D2XX drivers to be installed.

Download the project documentation and schematic in PDF format by clicking here.

Download the Delphi source code for the application by clicking here.

USB to a JTAG TAP Interface using FT2232H

Overview

This example project for the FT2232H demonstrates how to use the device's Multi-Protocol Synchronous Serial Engine (MPSSE) to make a USB to JTAG TAP test chain interface. The full project code is provided.

TI have a JTAG learning tool and accompanying abstract available on their website which is available for free download. Click here to visit the TI website.

Requirements

This project is designed to run on Windows 2000 or Windows XP and requires FTDI's D2XX drivers to be installed.

Download the project documentation and schematic in PDF format by clicking here.

Download the source code for the application by clicking here.

USB to JTAG Interface

Overview

This example project for the FT2232D demonstrates how to use the device's Multi-Protocol Synchronous Serial Engine (MPSSE) to make a USB to JTAG bus interface. The executable application and full project code (in Delphi) are provided.

TI have a JTAG learning tool and accompanying abstract available on their website which is available for free download. Click here to visit the TI website.

Requirements

This project is designed to run on Windows 2000 or Windows XP and requires FTDI's D2XX drivers to be installed.

Download the project documentation and schematic in PDF format by clicking here.

Download the Delphi source code for the application by clicking here.

USB to I2C Inteface using FT2232H

Overview

This example project for the FT2232H demonstrates how to use the device's Multi-Protocol Synchronous Serial Engine (MPSSE) to make a USB to I2C bus interface using the FT2232H. The executable application and full project code are provided.

Requirements

This project is designed to run on Windows 2000 or Windows XP and requires FTDI's D2XX drivers to be installed.

Download the project documentation and schematic in PDF format by clicking here.

Download the source code for the application by clicking here.

USB to I2C Inteface

Overview

This example project for the FT2232D demonstrates how to use the device's Multi-Protocol Synchronous Serial Engine (MPSSE) to make a USB to I2C bus interface. The executable application and full project code (in Delphi) are provided.

Requirements

This project is designed to run on Windows 2000 or Windows XP and requires FTDI's D2XX drivers to be installed.

Download the project documentation and schematic in PDF format by clicking here.

Download the Delphi source code for the application by clicking here.

USB to SPI Inteface using FT2232H

Overview

This example project for the FT2232H demonstrates how to use the device's Multi-Protocol Synchronous Serial Engine (MPSSE) to make a USB to SPI bus interface using the FT2232H Hi_Speed device. The executable application and full project code (in C++) are provided.

Requirements

This project is designed to run on Windows 2000 or Windows XP and requires FTDI's D2XX drivers to be installed.

Download the project documentation and schematic in PDF format by clicking here.

Download the C++ source code for the application by clicking here.

USB to SPI Interface

Overview

This example project for the FT2232D demonstrates how to use the devices Multi-Protocol Synchronous Serial Engine (MPSSE) to make a USB to SPI bus interface. The executable application and full project code (in Delphi) are provided.

Requirements

This project is designed to run on Windows 2000 or Windows XP and requires FTDI's D2XX drivers to be installed.

Download the project documentation and schematic in PDF format by clicking here.

Download the Delphi source code for the application by clicking here.

USB to SPI

Our thanks go to Bob Freeth for providing this VB6 example of using the FT2232D MPSSE for SPI communication with a MAX187 ADC.

Source code and executable are available for free download. This code is provided "as-is" for illustration purposes only and as such neither FTDI or Bob Freeth provide technical support for this VB6 code.