|
Based upon the FT32 high
performance, 32 bit RISC core, the FT9xx series provides a plethora of
connectivity options, making it the ideal choice for advanced technology
bridging solutions. By executing instructions from shadow RAM, rather than
flash memory, the FT9xx can operate at true Zero Wait States (0WS) up to
100MHz with 310 DMIPS performance.
A range of modules are provided, designed to assist with design and development with the series.
It's recommended to purchase the UMFTPD2A with the FT9xx Development
Development moudles during the evaluation and development phase as shown
in the diagram below.
The UMFTPD2A can be omitted during the production or
in-field updates phases as the IC can be programmed via USB DFU using the
USB Device Port directly on the FT9xx.
|
 |
MM900EV Development Modules |
|
|
The MM900EV development modules provide full hardware feature support for the FT90x MCU in a variety of form
factors.The modules also provide a connector for accessing external plug-in hardware over an SPI interface. Targeted
applications for the module include home security, HMI and automation systems,USB capability products,
embedded multimedia applications and a range of other industrial control systems. There are four module types available: the MM900EV1A, which comes
without a camera, MM900EV2A with a front-facing CMOS camera, MM900EV3A, equipped with a rear-facing CMOS camera. The MM900EV-Lite is optimized for HMI and embedded display applications.
Key Features: |
- FT90x 100-pin QFN package MCU.
- RJ45 with built in magnetics for 10/100Mbps Ethernet transfer.
- Standard USB-A connector to support USB device connection.
- Micro-B USB for connecting to a USB host or providing a power supply over USB.
- In built audio codec for stereo audio output with 3.5mm headphone jack and mono microphone input.
- Debugger interface for FT90x flash programming and EFUSE configuration.
- +5V alternative power supply DC connector.
- 2x5 pins 1.27mm pitch female Micro-MaTch connector for software download.
- 2x20 pins 2.54mm pitch female header support for external feature expansions.
- 24 pins 0.5mm pitch camera connector and two RGB LEDs (MM900EV2A/3A modules).
- MicroSD card socket supporting SD3.0 specification.
- 2x8 pins 2.54mm pitch dual entry female header and 16 pins 0.5mm pitch FFC/FPC connectors for SPI master to support LCD display modules.
- MM900EVxA Datasheet
- MM900EV-LITE Datasheet
|
 |
|
|
MM930Mini Module |
|
The MM930Mini Module is a USB microcontroller development module
in the Bridgetek product range. It utilizes the FT930Q bridge chip
which can handle all USB signalling and protocols. It is ideal for
development purposes to quickly prove functionality of adding USB to
a target design.
Key Features:
- USB 2.0 Hi-Speed compatible.
- Reduced development time
- Rapid integration into existing systems
- USB powered – no external power supply needed
- Based on the USB Hi-Speed FT930Q device
- Entire USB protocol handled by D2xx hardware engine
- USB micro-B connector common on many commercial devices
- On-board 500mA 3.3V LDO regulator, 12MHz crystal, 32kHz crystal
- Asynchronous Serial data transfer rates from 300 baud to 12
Mbaud at TTL levels
- One SPI master supports single / dual / quad modes of data
transfer. Clock rate is up to 25 MHz
- One SPI slave support single data transfer with 25MHz clock
- I2C bus interface can be configured as master or slave, with
data transfers up to 3.4Mbps
- UHCI / OHCI / EHCI host controller compatible
- One SPI slave support single data transfer with 25MHz clock
-
MM930Mini Module Datasheet
|
 |
|
|
MM930Lite Module |
|
The MM930Lite is a development module for Bridgetek’s 32-bit high performance FT93x Microcontroller family, which is used to develop and demonstrate the functionality of the FT93x Embedded Microcontroller, and is ideal for applications including home security systems, home automation systems, USB capability products, embedded multimedia application and other industrial control systems.
Key Features:
- USB 2.0 Hi-Speed compatible.
- Reduced development time
- Rapid integration into existing systems
- USB powered – no external power supply needed
- Based on the USB Hi-Speed FT930Q device
- Entire USB protocol handled by D2xx hardware engine
- USB micro-B connector common on many commercial devices
- On-board 500mA 3.3V LDO regulator, 12MHz crystal, 32kHz crystal
- Asynchronous Serial data transfer rates from 300 baud to 12
Mbaud at TTL levels
- One SPI master supports single / dual / quad modes of data
transfer. Clock rate is up to 25 MHz
- One SPI slave support single data transfer with 25MHz clock
- I2C bus interface can be configured as master or slave, with
data transfers up to 3.4Mbps
- UHCI / OHCI / EHCI host controller compatible
- One SPI slave support single data transfer with 25MHz clock
-
MM930Lite Module Datasheet
|
|
|
|
MM932LC |
|
The MM932LC is a low cost development module for
Bridgetek’s 32-bit high performance FT93x Microcontroller family,
which is used to develop and demonstrate the functionality of the
FT932 Embedded Microcontroller. The module is ideal for simple
applications including USB capability products, embedded multimedia
applications and other industrial control systems.
Key Features:
- FT932Q 48-pin QFN package microcontroller
- In built 16M Byte EFlash memory
- A Micro-B USB connector for connecting to a
USB host or providing a power supply over USB for the board
- 2×8 pins 2.54mm pitch dual entry female header for SPI
master to support LCD display modules
- 2×5 pins 1.27mm pitch female Micro-MaTch connector for
software download
- 1×15 pins 2.54mm pitch female header support for external
feature expansions
- Hardware Reset button provided
-
MM932LC Datasheet
|
|
| |
UMFTPD2A |
|
|
The UMFPD2A debugger/programmer module provides a USB bridge between the FT9xx
Eclipse IDE development tools runnng on a PC and the FT900 1-wire
debug pin. This module can be used to program and debug firmware running on the FT9xx series. Key Features: |
Hi-Speed
USB to one-wire interface converter
Hi-Speed USB to MPSSE interface converter
Hi-Speed USB to UART interface converter
Provides H/W Reset# signal
Provides multiple generic GPIO control signals
PWREN# line to control +5 power supply
Fuse protected with 0.5A hold current and schottky diode on the output power line
Two dedicated GPIOs to control VPP and FRSC power supplies
Three LEDs for power supply indication
2X5 way 1.27mm pitch Micor-MaTch socket
2X6 way 2.54mm pitch through hole pin header
Micro-B type USB port
Micro-MaTch Male to Male 10 pin ribbon cable
UMFTPD2A Datasheet |
|
|
|
Ordering Information |
|
| MM900EV1B |
FT90x Development Module |
|
| MM900EV3A |
FT90x Development Module with rear-facing CMOS camera |
|
| MM900EV-Lite |
Cut down FT90x Development Module |
|
| MM930Mini |
USB microcontroller development module |
|
| MM930Lite |
Development module for FT93x Microcontroller family |
|
| MM932LC |
Development module for FT93x Microcontroller family |
|
| VA-PSU-UK1 |
Accessory - UK Model 5V/1A USB Power Supply (Mfr # JX-B0520C-1-B) |
|
| VA-PSU-US1 |
Accessory - US Model 5V/1A USB Power Supply (Mfr # JX-B0520B-1-B) |
|
| VA-PSU-EU1 |
Accessory - EU Model 5V/1A USB Power Supply (Mfr # JX-B0520A-1-B) |
|
| ME810A-HV35R |
Daughter board - FT810 Development Module with 3.5 inch HVGA TFT LCD and fitted bezel |
|
| ME812A-WH50R |
Daughter board - FT812 Development Module with 5.0 inch WVGA TFT LCD and fitted bezel |
|
| ME813A-WH50C |
Daughter board - FT813 Development Module with 5.0 inch WVGA TFT LCD |
|
ME812AU-WH50R
|
Daughter
board - FT812 Development Module with 5.0 inch 800*480 TFT LCD |
|
ME813AU-WH50C
|
Daughter
board - FT813 Development Module with 5.0 inch 800*480 TFT LCD |
|
| VA-FC-1M-BKW |
Accessory - Flat USB A to Micro B Cable 1M - Black and White |
|
VA-FC-1M-BLW |
Accessory - Flat USB A to Micro B Cable 1M - Blue and White |
|
| UMFTPD2A |
Daughter board - MM900EV MCU Debugger Module |
|
|
|
|
FT9xx Toolchain |
|
|
Click
here to download the FT9xx Series Toolchain to enable code development and debug for the FT9xx series Development Modules.
|
