|
Vinculum-II Projects |
|
Listing
of example applications and projects for the FTDI
Vinculum (VNC2)
programmable USB 2.0 host / slave controller.
|
|
Vinculum II Android Open Accessory to USB Bridge Example |
|
This example describes how to use the Vinculum II (VNC2) to host an Android Open Accessory USB port and bridge to another USB peripheral e,g, the FT232.
A “C” source code example is provided to help the user get started with their own specific application.
For full details of this
project, please refer to Application Note
AN_323 - VNC2 Host to Android Open Accessory and FT232
Click here to download Vinculum II Android Open Accessory to USB Bridge Example project
files and source code
|
|
Vinco Volt Meter Example |
|
This example describes how to
use the Vinco module to drive the VNC2 PWM interface and convert
the generated waveform into an RMS voltage value for display on a oLED
display. “C” source code examples are provided to help the user get started with their own specific
application.
For full details of this
project, please refer to Application Note
AN_161 - Vinco Graphics Display Example
Click here to download Vinco Volt Meter Example project
files and source code
|
|
Vinco Graphics Display Example |
|
This is an example of how to
use the Vinco module to create and display graphic messages on a 128 x
64 pixel monochrome LCD display. “C” source code examples are also
provided to help the user get started with their own specific
application.
For full details of this
project, please refer to Application Note
AN_161 - Vinco Graphics Display Example
Click here to download
Vinco Graphics Display Example project files and source code
|
|
Vinco LCD Interface Example |
|
This is an example of how to use the
Vinco module to create and display text messages on a 2 line, 16 character, monochrome LCD display.
For full details of this
project, please refer to Application Note
AN_153 - Vinco LCD Interface Example
Click here to download
Vinco LCD Interface Example project files and source code
|
|
Vinculum-II Webcam Application Using OLED Display |
|
This application uses Vinculum-II to display images, obtained from a
webcam, on an OLED display.
The functionality is tightly coupled
to the hardware used, and as a result, the application note
covers only the minimum steps necessary to display images on the chosen
hardware.
Hardware Requirements:
- V2EVAL board
- 64-pin Vinculum II daughter board
- Logitech Webcam Pro 9000
- Densitron OLED display module
- SEPS525 160 RGB x 128 dots, 262K Colours PM-OLED Display Driver
and Controller
- 5V:12V DC to Dc converter to power OLED display
For full details of this project, please refer to
Application Note
AN_158 - Vinculum-II Webcam Application Using OLED Display
Click here to download
the project files and source code
|
|
DisplayWebcam - Vinculum-II
Webcam Application for Windows |
|
DisplayWebcam is an application that runs on a Windows PC. It can be
used to display images captured by a webcam, using a
V2-EVAL
board, on a
Windows PC screen. The source code is provided as an example and
is neither guaranteed or supported by FTDI.
The following are
required to run the webcam demo application:
- An FTDI V2-EVAL board loaded with webcam board side application.
(WebCam.rom can be flashed into the board using VinIDE).
- “Logitech webcam pro 9000” webcam connected to USB
(Port A) of V2-EVAL board.
- A Windows PC connected to UART of V2-EVAL board.
- The DisplayWebcam executable.
For full details of this project, please refer to
Application Note
AN_154 - Vinculum-II Webcam Application for Windows
Click here to download
DisplayWebcam project files and source code
|
|
Vinculum-II SD Card Example |
|
This project demonstrates how
to connect an SD Card to a
V2-EVAL board and then illustrates how to use FTDI's supplied
drivers to communicate with the SD Card using a FAT File System
interface.
For full details of this
project, please refer to Application Note
AN_155 - Vinculum-II SD Card Example
Click here to download
Vinculum-II SD Card Example project files and source code
|
|
Vinculum-II Bluetooth Dongle
Example |
|
This project shows how to
connect a Roving Networks USB-Bluetooth dongle to the Vinculum-II device
and transfer data wirelessly between the Vinculum-II device and another
Bluetooth device.
For full details of this project, please refer to
Application Note
AN_179 -Wireless Data Transfers using Vinculum-II
Click here to download Vinculum-II to Bluetooth example project
files and source code |
|
|
|